PubMed دسترسی آزاد

Initial Cytotoxicity of Additively and Subtractively Manufactured Resin-Based Materials for Interim Fixed Dental Prostheses: An In Vitro Study.

استودیوی صوتی مقاله

پخش حرفه‌ای فارسی و انگلیسی

در حال بررسی نسخه‌های صوتی ذخیره‌شده…

صوت تولیدشده با هوش مصنوعی است. برای کاربرد علمی یا درمانی، متن و منبع اصلی را بررسی کنید.
خواندن هوشمند فارسی و انگلیسی در حال آماده‌سازی صداهای مرورگر…
تنظیم صدای طبیعی و سرعت

صداهایی که در نامشان «Natural»، «Neural» یا «Online» دیده می‌شود معمولاً طبیعی‌ترند. انتخاب صدا به صداهای نصب‌شده در ویندوز و مرورگر شما بستگی دارد.

چکیده اصلی

OBJECTIVES: To compare the initial cytotoxic response of additively manufactured (AM) and subtractively manufactured (SM) resin-based materials for interim fixed dental prostheses (FDPs) under indirect and direct in vitro exposure conditions. MATERIAL AND METHODS: A total of 216 standardized resin discs were fabricated from AM resins (Group P, n = 108) and SM polymethyl methacrylate (PMMA)-based resins (Group M, n = 108). L929 mouse fibroblasts were used as the biological model, with a negative control group (Group C, n = 36). After 24 h of cell attachment, cell viability was assessed after 72 h under two conditions: indirect exposure to resin eluates and direct contact with resin discs. Viability was quantified by crystal violet staining. Data were analyzed using Kruskal-Wallis tests followed by Dunn's pairwise post hoc comparisons (α = 0.05). RESULTS: In the indirect assay, Group M showed 87% cell survival relative to the control, whereas Group P showed 65%; in the direct assay, values were 89% and 48%, respectively. Significant differences were observed among pooled groups in both assays (p < 0.001). Based on ISO 10993-5 thresholds, Group P was classified as slightly cytotoxic in the indirect assay and moderately cytotoxic in the direct assay, whereas Group M remained within the non-cytotoxic to slightly cytotoxic range. Group P showed significantly lower cell viability than Group M in both assays (adjusted p < 0.001), while no statistically significant differences were detected within each manufacturing category (adjusted p > 0.05). CONCLUSIONS: At 72 h, the tested AM resins showed significantly lower cell viability than the tested SM PMMA-based resins under the present in vitro conditions. CLINICAL SIGNIFICANCE: The lower cell viability observed for the tested 3D-printed interim materials under short-term in vitro conditions highlights the need for caution when extrapolating 72-h cell-viability findings to clinical performance and supports further standardized long-term in vitro and in vivo investigations.

متن کامل اصلی

نسخه دارای مجوز در منبع علمی در دسترس است.

لینک مستقیم از metadata منبع گرفته شده و در تب جدید باز می‌شود.

باز کردن متن کامل

کلیدواژه‌ها

cell survivalcytotoxicitydental materialsfibroblaststhree‐dimensional printing
در همین زیرشاخه

مقاله‌های مرتبط

PubMed2026

Failure of Wide-Diameter Dental Implants (Predominantly 5.0 mm) Show Distinct Risk Profiles-A Large Cohort Study.

AIM: To evaluate survival rates and identify temporally distinct risk factors for early and late failure of wide-diameter dental implants (≥ 5.0 mm) in a large real-world cohort using landmark analysis. MATERIALS AND METHODS: This retrospective cohort study analyzed 12 041 wide-diameter implants (≥ 5.0 mm), predominantly 5.0 mm, placed in 9247 patients at a single center between January 2014 and December 2023. Implant survival was defi…

PubMed2026

Influence of Air Polishing and Ultrasonics on Veneer Margins in Vitro: An Optical Coherence Tomography Pilot Study.

OBJECTIVE: In vitro evaluation of substance loss at the restoration margin of veneers was conducted as a function of prophylaxis procedures, air polishing, or ultrasonic instrumentation. MATERIALS AND METHODS: Forty-eight extracted premolars were restored with CAD/CAM materials after veneer preparation (t0): lithium disilicate, zirconia-reinforced lithium silicate ceramics, and resin-based composite. Five cycles of prophylaxis treatmen…

PubMed2026

Influence of Implant Type on Clinical and Radiologic Outcomes: A Cross-Sectional Private Practice-Based Analysis.

OBJECTIVES: To compare tissue-level (TL) and bone-level X (BLX) implants regarding peri-implant bone level alterations, survival, and complication rates over a 3-years. MATERIALS AND METHODS: In this retrospective, non-interventional clinical study, patients that had received either TL or BLX implants (both: Straumann AG), with at least one clinical follow-up (minimum 6 months), were included. Bone-level alterations and bone peaks were…

PubMed2026

Influence of Metal Artifact Reduction Algorithms on the Detection of Inferior Alveolar Canal Perforations by Zirconia Implants in CBCT Images.

INTRODUCTION: This study aims to evaluate the efficacy of a metal artifact reduction (MAR) algorithm in detecting contact between zirconia implants and inferior alveolar canal. MATERIALS AND METHODS: Twelve zirconia implants were placed in dry human mandibles using surgical guides, in two conditions: 1 mm above and within the canal. cone beam computed tomography (CBCT) was acquired with the MAR algorithm turned off and on. Three observ…